Tools Menu - This menu contains the basic tools of InfoSWMM SA that allow you to run the simulation and report the results. The basic modeling and analysis tools are incorporated into the Tools Menu.
When you define a scenario, you pick the facility, data, and option sets that comprise that scenario. When picking data sets for inclusion in a scenario, you may either specify that a data set associated with a given … Read the rest
The Dynamic Wave page of the Simulation Options dialog, shown below, sets several parameters that control how the dynamic wave flow routing computations are made. These parameters have no effect for the other flow routing … Read the rest
The flow classification summary report is available only if the flow routing option used is dynamic wave. This report summarizes the flow regimes experienced by all or selected conduits in the system.
The following variables are displayed on the … Read the rest
SWMM5 water quality can simulate the generation, inflow and transport of any number of user-defined pollutants. Required information for each pollutant includes:
| 1 | pollutant name |
| 2 | concentration units (i.e., milligrams/liter, micrograms/liter, or counts/liter) |
| 3 | concentration in rainfall |
| 4 | concentration in groundwater |
| 5 | concentration in |
The control of odorous gases and the corrosion of sewers are the two most important problems in operating wastewater collection systems. Evaluation of existing or potential odor or corrosion problems, and identification of where such problems will occur is, … Read the rest
Setting Controls For The Pumps and Orifices for the SWMM5 Engine in InfoSWMM and InfoSWMM SA
Using InfoSWMM H2OMap SWMM InfoSWMM SA , you may control the operational status of pumps and flow regulating structures by specifying their initial status, using the simple control rule, or using the RTC rule … Read the rest
The Pump Summary report table presents a summary of some pump result variables that could assist the modeler to easily analyze the drainage system.
The following variables are displayed on the pump summary report for all or … Read the rest
A data set is one of the three components that comprise a scenario. Data sets provide the capability to copy data (database information) in the active model and store that information separate from the … Read the rest
Information from the following sections of the SWMM5 project file are imported to InfoWorks ICM Subcatchment objects:
[SUBCATCHMENTS] Section
SWMM5 [SUBCATCHMENTS] are imported as InfoWorks ICM Subcatchments.
Geometry of the Subcatchment boundary is … Read the rest
Launch Scenario Explorer by selecting Scenario Explorer from the InfoSWMM and InfoSWMM SA Scenario Menu or by clicking the Scenario Explorer button (
) on the InfoSWMM H2OMap SWMM InfoSWMM SA Control Center Toolbar Standard … Read the rest
The Storage Summary report table presents a summary of some storage result variables that could assist the modeler to easily analyze the drainage system. Using this report results alone, the user can easily identify storage(s) that have … Read the rest
The Colorado Urban Hydrograph Procedure for InfoSWMM and InfoSWMM SA
The Colorado Urban Hydrograph Procedure (CUHP) uses the equations and procedures presented in the Urban Drainage Criteria Manual (USDCM) of the Urban Drainage and Flood Control District (UDFCD). Shape of the CUHP synthetic unit hydrograph is determined using the following … Read the rest
The General page of the Simulation Options dialog, shown below, sets values for the following options. In InfoSWMM v14.5 and above each tab is shown in two rows
Contents of this simulation option dialog page are described … Read the rest
Shown below is a definition sketch of the two-zone groundwater model that is used in InfoSWMM H2OMap SWMM InfoSWMM SA . The upper zone is unsaturated at a varying moisture content of θ. The lower zone is … Read the rest
The Export Manager enables the modeler to export InfoSWMM H2OMap SWMM 's element data (both graphical details and attribute data).
Click on the following links for more information:
To Launch … Read the rest
The Junction Summary report table presents a summary of some junction result variables that could assist the modeler to easily analyze the drainage system. Using this report results alone, the user can easily identify junction (s) that … Read the rest
The Conduit Summary report table presents a summary of some conduit result variables that could assist the modeler to easily analyze the drainage system. Using these report results alone, the user can easily identify conduit(s) that have … Read the rest
InfoSewer versus InfoSWMM versus ICM
A short comparison of the features in InfoSWMM, ICM and InfoSewer. Many of the same rows apply to H2OMap SWMM, InfoSWMM SA and H2OMap Sewer.
| Feature Class | Feature | InfoSewer | InfoSWMM | ICM | |
| Base Functionality | Conservative Solution as an option |  |
|
 |
|
| Public Domain engine | |
|
|
||
| Calibrate model to flow | |||||
Like all other visual data objects, pump object is edited using the attribute browser.
To edit attributes of a pump;
from InfoSWMM H2OMap SWMM InfoSWMM SA Edit Network tool 
